How to Install ATV and UTV Axles Correctly and Make Them Last Longer
A heavy-duty axle such as Rhino 2.0 or Assault Industries MAS-223 Phoenix is much stronger than a stock axle, but how it is installed and how the vehicle is ridden still decide how long it lasts. Most axle failures we see are caused by installation mistakes, damaged boots or riding beyond the joint's limits, not by the axle itself. This guide explains how to install your new axles correctly and how to look after them.
Before you start
- Check fitment. Make sure the axle is listed for your exact vehicle model and year, and for the correct position (front or rear). On the product page, check the fitment list and the OEM part number the axle replaces. For example, the MAS-223 Phoenix for Maverick R replaces OEM part 705402490.
- Check your setup. A lift kit, long-travel or offset A-arms, a different ride height or larger tires all change the angle the CV joints work at. Tell us about any modifications before you order, and we will check which axle suits your setup.
- Use the service manual. Torque values for hub nuts, wheel nuts and suspension bolts are specific to your vehicle. Always use the values from your vehicle's service manual and the axle manufacturer's instructions.
- Tools. Basic hand tools, a torque wrench, and for stuck inner CV joints a CV axle puller. You can find one in our shop: CV Axle Puller for ATV/UTV.
Removing the old axle
- Park the vehicle on a flat surface, secure it, and lift and support it safely on stands.
- Remove the wheel, the hub nut and anything that has to come off to free the axle, following your service manual.
- Pull the outer end out of the hub, then pull the inner CV joint straight out of the differential or gearbox. Pull on the CV cup, not on the axle shaft, and do not hammer on the CV joint or the boot. A stuck joint comes out easiest with a CV axle puller.
- Check the differential seal and the splines in the hub. A leaking seal or damaged splines will damage your new axle too, so fix them first.
Installing the new axle
- Clean the splines in the differential and hub, and check that the retaining clip (circlip) on the inner end of the new axle is in place.
- Do not let the axle hang on its CV joints. Support the axle while you fit it, so the joints are not bent to their limit and the boots are not stretched or pinched.
- Push the inner end fully into the differential until the clip locks. Then pull firmly on the CV cup by hand. If it moves out, it is not seated. An axle that is not fully seated is one of the most common causes of broken CV joints.
- Fit the outer end into the hub and reassemble the suspension parts. Tighten everything to the service manual torque values, including the hub nut.
- Check the boots. They must not be twisted, pinched or touching any part of the suspension, and the boot clamps must be tight.
- Cycle the suspension and steering. With the wheels off the ground, turn the steering from lock to lock and move the suspension through its travel. Nothing should bind, rub or touch the boots.
After installation
- Take a short, easy test ride, then check again that the axle is seated and that the hub nut is still at the correct torque.
- Re-check bolts and boots after the first few hours of riding.
How to ride so your axles last longer
Even the strongest axle has limits. Rhino 2.0 axles, for example, are designed to break before your more expensive differential does. Riding habits make the biggest difference:
- Don't land jumps with the throttle on. When spinning wheels suddenly touch the ground, the shock goes straight through the axles. Let off the throttle before landing.
- Avoid heavy throttle at full steering lock, especially with 4WD or the front differential lock engaged. This is when the front CV joints work at their highest angle and load.
- Don't spin the wheels on rocks or hard ground and then let them catch suddenly.
- Respect the joint's angle limits. Extra lift, long-travel arms or full suspension droop increase the CV angle. Make sure your axles are rated for your setup.
- Bigger tires and more power mean more load. Larger or heavier tires, a tune or clutch changes all put more stress on the axles.
- Heat is the CV joint's enemy. Long, fast runs heat up the grease. Assault Industries' Phoenix axles use a high-temperature grease that, according to the manufacturer, stayed stable up to 308°C (586°F) in lab testing, while the stock grease broke down at around 185°C (365°F). Whatever axle you use, a damaged boot that lets grease out quickly leads to an overheated, failing joint.
Maintenance: check the boots after every ride
The rubber or TPE boot keeps the grease in and the dirt and water out. A torn boot is the most common reason a good axle fails early.
- After every ride, look at all inner and outer boots for cuts, tears, grease leaks and loose clamps.
- Replace a damaged boot straight away. If dirt or water has already got inside, clean and re-grease the joint before fitting the new boot. For Rhino axles we sell replacement boot kits in rubber or high-strength TPEE, with clip, bands and grease. The axle's SKU number is printed on the shaft, so you can find the right kit. "Inner" is the end closest to the centre of the vehicle, and "outer" is the end closest to the wheel.
- Listen and feel. Clicking when turning, vibration or play in the axle are early signs of a worn CV joint. Stop and check before it breaks.
- Be careful with pressure washers. Don't spray directly at the boots from close range.
Warranty
All axles we sell come with a 12-month warranty. Warranty covers manufacturing defects, not damage from incorrect installation, damaged boots or use outside the axle's limits. Please note that items used in any type of racing are not covered by warranty, as described in our Refund and Warranty Policy. If you have a problem, email sales@lizardwarehouse.com with your order number, a description of what happened and clear photos of the axle, including the part number on the shaft. We handle all warranty claims for you in Europe.
Need help choosing an axle?
Send us your vehicle model, year and any modifications (lift, arms, tire size, tune), and we will recommend the right axle for your setup before you order.
